您好,欢迎来到机械CAD网!
客服QQ:20425042

首页 > 冲压模具 >

设计名称
轻型卡车加强筋弯曲模设计【说明书+CAD】
设计编号
JX6912
设计软件
AutoCAD,Word
包含内容
见右侧图片
说明字数
见下方截图
图纸数量
见右侧图片
推荐指数
较高
价格
价格优惠中
整理日期
2018-10-23
整理人
admin
设计简介
摘要
目前,在我国日常的工业生产中轻型卡车的使用范围很广,但在生产轻型卡车时,车厢加强筋使用量很大,并且在折弯机上加工时会出现弯曲困难,加工时间过长,损耗弯折机寿命等问题,对轻型卡车车厢的加强筋弯曲模进行设计,可缩短加强筋弯曲的时间,使成型效果更好,而且降低成本,有助于加快经济发展。因此本设计对现实生产生活有着重要意义。
首先分析了制造轻型卡车加强筋的材料的工艺性并确定了合适的尺寸,然后计算弯曲部分的最小弯曲半径,弯曲弹复角以及坯料的精确长度。最后,根据计算结果确定所要运用的弯曲工艺方案。从上述力的分析中,计算材料的弯曲应力并选择合适压力机。计算凹凸模的外形尺寸并确定其制造和组装精度,接着确定固定板和上下模座的尺寸。选择合适零件,如:顶件板,定位板和弹顶器等,并确定顶件板尺寸。基于上述数据最终确定了压力机的型号。最后,根据以上计算结果使用AUTOCAD绘图软件绘制模具的总装配图和部分重要零件的零件图。
 
关键词 轻型卡车;加强筋;弯曲模;模具设计
 
 Abstract
At present, Light trucks are widely used in China's daily industrial production, but the amount of reinforcing rib in light truck carriage is large, bending on the bending machine is time-consuming and laborious, and losses the service life of the bending machine. the design of the bending die of reinforcing rib in light truck carriage can improve the forming efficiency and forming effect of reinforcing rib, and the cost is low, which is helpful to accelerate the economic development. Therefore, the research of this topic is of great significance to actual production and life.
In this paper, the process analysis was carried out according to the material and size of the light truck ribs. The minimum bending radius and the bending complex radius of the bending part were determined and the length of the blank was calculated. Finally, determine the bending process plan. By analyzing the above forces, the bending stress of the material is calculated and a suitable press is selected. Calculate the external dimensions of the concave-convex mold and determine its manufacturing and assembly accuracy, and then determine the dimensions of the fixed plate and upper and lower mold seats. Select suitable parts, such as top plate, locating plate and ejector, and determine the size of top plate.Finally, the model of the press was determined based on the above data.Finally, use AUTOCAD software to draw the assembly drawings of the mold and the parts drawings of important parts such as male and female molds. The design of stiffener bending die was finally completed.
 
Keywords   light truck   rib reinforcement   bending die   die design 

目       录
摘要 I
Abstract II
1 绪论 1
1.1 设计的目的及意义 1
1.2 国内外的发展现状 1
1.2.1 模具发展现状 1
1.2.3 主要设计内容 3
2零件的工艺性分析和实验方案论证 4
2.1零件的工艺性分析 4
2.1.1零件材料的选择 4
2.1.2零件结构 4
2.1.3最小许可弯曲半径 4
2.1.4 弯曲件的直边高度 5
2.1.5 对称性工件的圆角半径的设置 5
2.1.6 零件尺寸的精度 5
2.1.7 零件弯曲时的回弹 6
2.1.8 弯曲件展开长度的计算 6
2.2 弯曲工艺方案的确定及弯曲模结构的设计原则 7
2.2.1 弯曲工艺方案的论证 7
2.2.2 弯曲模结构设计原则 8
3 弯曲力的计算和压力机的选用 9
3.1弯曲力的计算 9
3.1.1 第一阶段自由弯曲力的计算 9
3.1.2 第二阶段校正力的计算 10
3.1.3 顶件力的计算 10
3.2 弯曲时压力机压力的确定和压力机型号的初步确定 11
3.2.1 弯曲时压力机压力的确定 11
3.2.2 压力机型号的确定 11
4 弯曲凸、凹模设计 14
4.1 弯曲凸、凹模的间隙确定 14
4.2 弯曲模工作部分尺寸计算 15
4.2.1 凸凹模宽度尺寸的计算 15
4.2.2 凸、凹模的圆角半径确定 16
4.3 凹模外形尺寸设计 16
4.4 凹模强度校核 17
4.5 凸模设计 18
4.6 凸模强度校核 18
4.7 弯曲件凸、凹模深度及凸模两侧部分尺寸的确定 19
4.8 凸、凹模的固定 20
4.9 弯曲件凸、凹模材料的选用及热处理 20
5.1 固定板的设计计算 24
5.1.1凹模固定板的设计 24
5.1.2 凸模固定板的设计 25
5.2 凹模垫板 26
5.3 顶件装置设计 27
5.4 弯曲模下模座的设计 28
5.5 定位零件的设计计算 29
5.6 弹性元件的设计计算 30
5.8 模具总装配图 33
6 压力机的最终确定 34
结论 35
致谢 36
参考文献 37
 
部分图纸截图
展开
  • 在线咨询
  • QQ:20425042
  • QQ:99872184
  • 技术支持
  • 售后服务